Geo Denso Heater Core Information

DENSO REGULAR CLASS OXYGEN SENSOR

Denso Regular Class Oxygen Sensors are specifically designed to meet the challenging demands of today's engines. Each of Denso's Oxygen Sensor is constructed from the highest quality materials available. Manufactured to the OE standards and subjected to rigorous safety and performance tests.

Specifications:

• 4-wire
• 11.77 in. lead wire
• Non-flanged

Features:

• Constructed from high quality stainless steel, porous polytetrafluoroethylene, fluorine rubber, aluminum oxide, high-grade platinum, and ceramics
• Double protection layer
• Aluminum oxide trap layer
• Porous PTFE filter
• Stainless steel housing

1 required per vehicle. Requires wire splicing and electrical installation. Reuse your old connector.

Location: After Catalytic Converter

Type: OE replacement, 4-wire

Quantity Sold: Sold individually

Warranty: 12-month Denso limited warranty

Part #: NP2344209

DENSO REGULAR CLASS OXYGEN SENSOR

Denso Regular Class Oxygen Sensors are specifically designed to meet the challenging demands of today's engines. Each of Denso's Oxygen Sensor is constructed from the highest quality materials available. Manufactured to the OE standards and subjected to rigorous safety and performance tests.

Specifications:

• 4-wire
• 11.77 in. lead wire
• Non-flanged

Features:

• Constructed from high quality stainless steel, porous polytetrafluoroethylene, fluorine rubber, aluminum oxide, high-grade platinum, and ceramics
• Double protection layer
• Aluminum oxide trap layer
• Porous PTFE filter
• Stainless steel housing

1 required per vehicle. Requires wire splicing and electrical installation. Reuse your old connector.

Location: Before Catalytic Converter

Type: OE replacement, 4-wire

Quantity Sold: Sold individually

Warranty: 12-month Denso limited warranty

Part #: NP2344209

ACCEL HEI REMOTE MOUNT SUPER COIL, BLACK/YELLOW, SOLD INDIVIDUALLY -- 0.3 ohm primary resistance, 8.8k ohm secondary resistance, 134:1 turns ratio, 48,000 V maximum voltage, male/HEI wire attachment style, E-core style, epoxy internal construction, square; Does not include mounting bracket, coil wire and ballast resistor; Offers significant peak increases of 36 percent in energy and 27 percent in voltage against OE; Features brass contact that increases energy transfer and resists corrosion better than aluminum; Engineered with optimized low resistance; High turns ratio windings around an M36 high Silicone magnetic steel E-core; Delivers quicker starts, improved idle quality, crisper throttle response, and higher RPM power; A direct bolt-in, plug-In replacement; Can work with an Accel, Mallory, Crane, Holley or MSD capacitive discharge ignition system; Special high temperature epoxy resists shock and vibration while increasing thermal conductivity.

Quantity Sold: Sold individually

Warranty: 90-day Accel limited warranty

Part #: A35140011

MSD BLASTER SS COIL, RED -- 3.500 in. L x 2.230 in. W x 2.650 in. H, 0.355 ohms primary resistance, 4.4 K ohms secondary resistance, 48,000 V maximum voltage, 6.9 mH inductance, 300 mA peak current, 220 uS spark duration, 70:1 turns ratio, male/HEI wire attachment style, E-core style, square; Includes 3 vibration mounts and hardware, 90 degree MSD spark plug boot and 90 degree dual crimp terminal; Does not include mounting bracket, coil wire, and ballast resistor; CARB E.O. approved; Efficient winding design and assembly creates a compact housing; Improved output coil for electronic ignitions and MSD Ignitions; Primary and secondary windings are encased in Ciba polyurethane; Features DuPont Rynite housing with a tall tower and brass primary terminals.

Type: Universal product

Quantity Sold: Sold individually

Warranty: 1-year MSD limited warranty

Part #: M468207

GATES SS HEATER HOSE -- 0.625 in. ID, 60 psi working pressure; Features good resistance to high temperatures and non-oil based coolant additives and moderate resistance to oil and grease contamination; Tested to assure reliability; A high quality, direct fit OE replacement heater hose; Similar to SAE 20R3 class D-2; Do not use for fuel or oil transfer applications.

Quantity Sold: Sold individually

Warranty: Lifetime Gates limited warranty

Part #: GAT28411

ZEROSTART TANK-TYPE ENGINE HEATER

• Fast starts all winter long

Built-in thermostat prevents overheating and burnout. Keeps engine warm by circulating warm engine coolant through entire engine. Quicker heater and defroster output. Connects to 5/8" heater hose-operates on regular AC house current. 120 volt. With 1-ft. grounded cord and instructions.
750-Watt.Warms 4-cylinder engines in 2-3 hours, 6-cylinder engines overnight.
Imported Car Adapter.Adapter required for all Mercedes (Not included).

Quantity Sold: Sold individually

Part #: ZER3308001

4-SEASONS CAP AND VALVE A/C SYSTEM SEAL KIT -- A high quality, direct fit OE cap and valve A/C system seal kit.

Quantity Sold: Kit

Warranty: 120-day 4-Seasons limited warranty

Part #: FS26777

DAYCO HEATER HOSE -- Curved; Single long hose, 0.62 in. ID, 18 in. trunk H; Features knitted reinforcement and all synthetic EPDM construction provides the high strength and resistance to oil, mud, salt, road debris, ozone, coolants, and temperature variations of less than 40 degrees Fahrenheit to more than 257 degrees Fahrenheit that are required for OEM hose replacements; The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Quantity Sold: Sold individually

Warranty: Dayco limited warranty

Part #: DY80402

DENSO PREMIUM CLASS IRIDIUM SPARK PLUG

Denso's Premium Class Iridium Spark Plugs is fast becoming the standard for today's high-tech engines. Employing a revolutionary 360 degrees laser welding process, Denso has created a spark plug unlike anything on the market today. Designed for durability under the most extreme conditions. Denso's patented Iridium alloy is 6 times harder and 8 times stronger than conventional platinum and can handle temperatures in excess of 4,000 degrees Fahrenheit.

Specification:

• 14 mm thread size
• 19 mm reach
• 0.63 in. hex size
• 0.04 in. gap size
• Gasket seat style
• Resistor plug type
• 0.4 mm iridium center electrode
• Tapered cut U-groove ground electrode
• Removable terminal
• Heat range 16

Features:

• Designed with heavy duty insulator that provides unparalleled dielectric strength and thermal conductivity under extreme temperatures
• Five-rib design prevents flashover while decreasing voltage loss
• Copper glass seal bonds the center electrode and insulator together for a gas-tight seal
• Platinum center electrode utilizes platinum to shrink the surface area of the center electrode tip for maximum firing performance and minimum voltage requirements
• Platinum ground electrode resists gas and electrical erosion and corrosion extending service intervals to 60,000 miles

Series: Denso Iridium Power

Quantity Sold: Sold individually

Warranty: 12-month Denso limited warranty

Part #: NP5301

HEATER CRAFT HEATER KIT, STEEL, POWDERCOATED BLACK -- 28,000 BTU per hour; 263 CFM; 3-speed 12V blower; Includes heater, mounting brackets, wiring harness, switch and bracket, stainless steel mounting hardware, and instructions; With ducts; Housing is made from heavy duty steel; Uses warm engine coolant to keep you comfortable during cold weather or when driving with the top down; 3-speed operation ranging from 172 CFM, 228 CFM, up to 263 CFM; Heater hose not included.

Quantity Sold: Kit

Part #: HTR200H