Plymouth Denso Heater Core Information

DENSO REGULAR CLASS OXYGEN SENSOR

Denso Regular Class Oxygen Sensors are specifically designed to meet the challenging demands of today's engines. Each of Denso's Oxygen Sensor is constructed from the highest quality materials available. Manufactured to the OE standards and subjected to rigorous safety and performance tests.

Specifications:

• 4-wire
• 11.77 in. lead wire
• Non-flanged

Features:

• Constructed from high quality stainless steel, porous polytetrafluoroethylene, fluorine rubber, aluminum oxide, high-grade platinum, and ceramics
• Double protection layer
• Aluminum oxide trap layer
• Porous PTFE filter
• Stainless steel housing

1 required per vehicle. Requires wire splicing and electrical installation. Reuse your old connector.

Location: After Catalytic Converter

Type: OE replacement, 4-wire

Quantity Sold: Sold individually

Warranty: 12-month Denso limited warranty

Part #: NP2344209

DENSO REGULAR CLASS OXYGEN SENSOR

Denso Regular Class Oxygen Sensors are specifically designed to meet the challenging demands of today's engines. Each of Denso's Oxygen Sensor is constructed from the highest quality materials available. Manufactured to the OE standards and subjected to rigorous safety and performance tests.

Specifications:

• 4-wire
• 11.77 in. lead wire
• Non-flanged

Features:

• Constructed from high quality stainless steel, porous polytetrafluoroethylene, fluorine rubber, aluminum oxide, high-grade platinum, and ceramics
• Double protection layer
• Aluminum oxide trap layer
• Porous PTFE filter
• Stainless steel housing

1 required per vehicle. Requires wire splicing and electrical installation. Reuse your old connector.

Location: Before Catalytic Converter

Type: OE replacement, 4-wire

Quantity Sold: Sold individually

Warranty: 12-month Denso limited warranty

Part #: NP2344209

DENSO SUPER CLASS ALTERNATOR, NEW -- Precision designed and performance tested OE-standard quality alternator; Features a housing tapped to OEM specifications and damaged-checked for heat warping, corrosion or improper surface alignment; Has performance and insulation tested rotor and stator to 600 volts, packed bearing with OEM grade lubricant, up to 300 volts performance tested rectifier, and 100 percent stripped and replated hardware; Its slip ring is rematched to an average of 8 microns or 20 microns run-out maximum; With 12-month unlimited-mile Denso warranty.

Condition: New

Quantity Sold: Sold individually

Warranty: 12-month or unlimited-mile Denso limited warranty

Part #: NP2110105

MSD REPLACEMENT COIL, 2-PIN CONNECTOR, RED -- 3.962 in. L x 1.757 in. W x 2.968 in. H, 1.2 ohms primary resistance, 13.7 K ohms secondary resistance, 35,000 V maximum voltage, 3.9 mH inductance, 70:1 turns ratio, male/HEI wire attachment style, E-core style, square; Does not include mounting bracket, coil wire, and ballast resistor; Epoxy internal construction; CARB E.O. approved; A direct replacement for late model Dodges; Works with stock ignition as well as MSD ignitions.

Quantity Sold: Sold individually

Warranty: 1-year MSD limited warranty

Part #: M468228

GATES DURION HEATER HOSE -- A High Quality Heater Hose, Centerline Length 50 ft., I.D. 0.75

Quantity Sold: Sold individually

Warranty: Lifetime Gates limited warranty

Part #: GAT28412

DENSO SUPER CLASS FIRST TIME FIT OXYGEN SENSOR

Denso Super Class First Time Fit Oxygen Sensors are specifically designed to meet the challenging demands of today's engines. Each of Denso's Oxygen Sensor is constructed from the highest quality materials available. Manufactured to the OE standards and subjected to rigorous safety and performance tests.

Specifications:

• 4-wire
• 22.8 in. lead wire

Features:

• Constructed from high quality stainless steel, porous polytetrafluoroethylene, fluorine rubber, aluminum oxide, high-grade platinum, and ceramics
• Double protection layer
• Aluminum oxide trap layer
• Porous PTFE filter
• Stainless steel housing

1 required per vehicle. This part does not require wire cutting.

Location: After Catalytic Converter

Type: OE replacement, 4-wire

Quantity Sold: Sold individually

Warranty: 12-month Denso limited warranty

Part #: NP2344076

DENSO REGULAR CLASS TRADITIONAL SPARK PLUG, SOLD INDIVIDUALLY -- 14 mm thread, 19 mm reach, 0.62 in. hex size, gasket seat, resistor type, solid terminal, projected tip, U-groove ground electrode, 0.044 in. gap, heat range 16; Designed with heavy duty insulator that provides unparalleled dielectric strength and thermal conductivity under extreme temperatures; Five-rib design prevents flashover while decreasing voltage loss; Copper glass seal bonds the center electrode and insulator together for a gas-tight seal; Platinum center electrode utilizes platinum to shrink the surface area of the center electrode tip for maximum firing performance and minimum voltage requirements; Platinum ground electrode resists gas and electrical erosion and corrosion extending service intervals to 60,000 miles.

Series: Denso Standard

Quantity Sold: Sold individually

Warranty: 12-month Denso limited warranty

Part #: NPK16PRU11

MSD BLASTER SS COIL, RED -- 3.500 in. L x 2.230 in. W x 2.650 in. H, 0.355 ohms primary resistance, 4.4 K ohms secondary resistance, 48,000 V maximum voltage, 6.9 mH inductance, 300 mA peak current, 220 uS spark duration, 70:1 turns ratio, male/HEI wire attachment style, E-core style, square; Includes 3 vibration mounts and hardware, 90 degree MSD spark plug boot and 90 degree dual crimp terminal; Does not include mounting bracket, coil wire, and ballast resistor; CARB E.O. approved; Efficient winding design and assembly creates a compact housing; Improved output coil for electronic ignitions and MSD Ignitions; Primary and secondary windings are encased in Ciba polyurethane; Features DuPont Rynite housing with a tall tower and brass primary terminals.

Type: Universal product

Quantity Sold: Sold individually

Warranty: 1-year MSD limited warranty

Part #: M468207

GATES SS HEATER HOSE -- 0.625 in. ID, 60 psi working pressure; Features good resistance to high temperatures and non-oil based coolant additives and moderate resistance to oil and grease contamination; Tested to assure reliability; A high quality, direct fit OE replacement heater hose; Similar to SAE 20R3 class D-2; Do not use for fuel or oil transfer applications.

Location: Upper Or Lower

Quantity Sold: Sold individually

Warranty: Lifetime Gates limited warranty

Part #: GAT28411

GATES SS HEATER HOSE -- 0.625 in. ID, 60 psi working pressure; Features good resistance to high temperatures and non-oil based coolant additives and moderate resistance to oil and grease contamination; Tested to assure reliability; A high quality, direct fit OE replacement heater hose; Similar to SAE 20R3 class D-2; Do not use for fuel or oil transfer applications.

Quantity Sold: Sold individually

Warranty: Lifetime Gates limited warranty

Part #: GAT28411