GMC Denso Throttle Body Information

DIRECT REPLACEMENT TWO BARREL THROTTLE BODY -- Direct Replacement For OE, Provides Increased Torque And Horsepower Up To 25%, 670 CFM, 50 State Legal, Bolt On Installation

Material: Aluminum

Type: Direct OE replacement

Condition: New

Quantity Sold: Sold individually

Part #: H195025

DENSO REGULAR CLASS OXYGEN SENSOR

Denso Regular Class Oxygen Sensors are specifically designed to meet the challenging demands of today's engines. Each of Denso's Oxygen Sensor is constructed from the highest quality materials available. Manufactured to the OE standards and subjected to rigorous safety and performance tests.

Specifications:

• 4-wire
• 11.77 in. lead wire
• Non-flanged

Features:

• Constructed from high quality stainless steel, porous polytetrafluoroethylene, fluorine rubber, aluminum oxide, high-grade platinum, and ceramics
• Double protection layer
• Aluminum oxide trap layer
• Porous PTFE filter
• Stainless steel housing

1 required per vehicle. Requires wire splicing and electrical installation. Reuse your old connector.

Location: Driver Side, Before Catalytic Converter

Type: OE replacement, 4-wire

Quantity Sold: Sold individually

Warranty: 12-month Denso limited warranty

Part #: NP2344209

DENSO REGULAR CLASS OXYGEN SENSOR

Denso Regular Class Oxygen Sensors are specifically designed to meet the challenging demands of today's engines. Each of Denso's Oxygen Sensor is constructed from the highest quality materials available. Manufactured to the OE standards and subjected to rigorous safety and performance tests.

Specifications:

• 4-wire
• 11.77 in. lead wire
• Non-flanged

Features:

• Constructed from high quality stainless steel, porous polytetrafluoroethylene, fluorine rubber, aluminum oxide, high-grade platinum, and ceramics
• Double protection layer
• Aluminum oxide trap layer
• Porous PTFE filter
• Stainless steel housing

1 required per vehicle. Requires wire splicing and electrical installation. Reuse your old connector.

Location: After Catalytic Converter

Type: OE replacement, 4-wire

Quantity Sold: Sold individually

Warranty: 12-month Denso limited warranty

Part #: NP2344209

DENSO REGULAR CLASS OXYGEN SENSOR

Denso Regular Class Oxygen Sensors are specifically designed to meet the challenging demands of today's engines. Each of Denso's Oxygen Sensor is constructed from the highest quality materials available. Manufactured to the OE standards and subjected to rigorous safety and performance tests.

Specifications:

• 4-wire
• 11.77 in. lead wire
• Non-flanged

Features:

• Constructed from high quality stainless steel, porous polytetrafluoroethylene, fluorine rubber, aluminum oxide, high-grade platinum, and ceramics
• Double protection layer
• Aluminum oxide trap layer
• Porous PTFE filter
• Stainless steel housing

1 required per vehicle. Requires wire splicing and electrical installation. Reuse your old connector.

Location: Driver Side, After Catalytic Converter

Type: OE replacement, 4-wire

Quantity Sold: Sold individually

Warranty: 12-month Denso limited warranty

Part #: NP2344209

DENSO REGULAR CLASS OXYGEN SENSOR

Denso Regular Class Oxygen Sensors are specifically designed to meet the challenging demands of today's engines. Each of Denso's Oxygen Sensor is constructed from the highest quality materials available. Manufactured to the OE standards and subjected to rigorous safety and performance tests.

Specifications:

• 4-wire
• 11.77 in. lead wire
• Non-flanged

Features:

• Constructed from high quality stainless steel, porous polytetrafluoroethylene, fluorine rubber, aluminum oxide, high-grade platinum, and ceramics
• Double protection layer
• Aluminum oxide trap layer
• Porous PTFE filter
• Stainless steel housing

1 required per vehicle. Requires wire splicing and electrical installation. Reuse your old connector.

Location: Before Catalytic Converter

Type: OE replacement, 4-wire

Quantity Sold: Sold individually

Warranty: 12-month Denso limited warranty

Part #: NP2344209

DENSO REGULAR CLASS TRADITIONAL SPARK PLUG

Denso's Regular Class Traditional Spark Plugs guarantee the quality of the product they produce because every component that leaves their factories has been designed with precision, manufactured to the strictest OE standards and subjected to rigorous safety and performance tests.

Specification:

• 14 mm thread size
• 18 mm reach
• 0.63 in. hex size
• 0.06 in. gap size
• Tapered seat style
• Resistor plug type
• U-groove ground electrodes
• Removable terminal
• Projected tip
• Heat range 16

Features:

• Designed with heavy duty insulator that provides unparalleled dielectric strength and thermal conductivity under extreme temperatures
• Copper glass seal bonds the center electrode and insulator together for a gas-tight seal
• Platinum center electrode utilizes platinum to shrink the surface area of the center electrode tip for maximum firing performance and minimum voltage requirements
• Platinum ground electrode resists gas and electrical erosion and corrosion extending service intervals to 60,000 miles

Series: Denso Standard

Quantity Sold: Sold individually

Warranty: 12-month Denso limited warranty

Part #: NP5023

DENSO SUPER CLASS FIRST TIME FIT COMPRESSOR, NEW -- With clutch; Built with superior air conditioning components to meet the stringent requirements of carmakers throughout the world for high output, extended reliability and reduced noise, vibration and harshness; Guaranteed to last longer and perform better; With 12-month Denso limited warranty.

Condition: New

Quantity Sold: Sold individually

Part #: NP4719166

PERFORMANCE ACCESSORIES BODY LIFT KIT -- 3 in. lift; Includes high grade nylon-reinforced lift blocks, rust-resistant front and rear bumper brackets, steering extension, fuel filler extension, steering extension tubes, cab safety straps, harness clamps, crush blocks, Loctite adhesive, mounting hardware, and installation instructions; Does not include gap guards; Made from grade 5 zinc plated material using state of the art CNC equipment; Allows the increase of tire size for greater ground clearance and rugged look; Does not alter or change suspension components and will not deteriorate factory ride quality nor void vehicle warranty; Gap guards recommended to keep the engine compartment clean; Not for vehicles with diesel engine; Cannot be used for towing; With Performance Accessories limited warranty.

Location: Rear

Type: Direct fit

Quantity Sold: Kit

Warranty: Performance Accessories limited warranty

Part #: P6410103

PERFORMANCE ACCESSORIES BODY LIFT KIT -- 2 in. lift; Includes high grade nylon-reinforced lift blocks, rust-resistant front and rear bumper brackets, steering extension, transmission shift extension, heater hose extension, brake booster hose, fuel filler vent hose, fuel filler extension hose, Loctite adhesive, mounting hardware, and installation instructions; Does not include gap guards; Made from grade 5 zinc plated material using state of the art CNC equipment; Allows the increase of tire size for greater ground clearance and rugged look; Does not alter or change suspension components and will not deteriorate factory ride quality nor void vehicle warranty; Gap guards recommended to keep the engine compartment clean; May require air intake or air intake hose modification for vehicles with Vortec V-6; Cannot be used for towing; With Performance Accessories limited warranty.

Type: Direct fit

Quantity Sold: Kit

Warranty: Performance Accessories limited warranty

Part #: P64102

DENSO PREMIUM CLASS IRIDIUM SPARK PLUG

Denso's Premium Class Iridium Spark Plugs is fast becoming the standard for today's high-tech engines. Employing a revolutionary 360 degrees laser welding process, Denso has created a spark plug unlike anything on the market today. Designed for durability under the most extreme conditions. Denso's patented Iridium alloy is 6 times harder and 8 times stronger than conventional platinum and can handle temperatures in excess of 4,000 degrees Fahrenheit.

Specification:

• 14 mm thread size
• 18 mm reach
• 0.63 in. hex size
• 0.04 in. gap size
• Tapered seat style
• Resistor plug type
• 0.4 mm iridium center electrode
• Tapered cut U-groove ground electrode
• Removable terminal
• Heat range 16

Features:

• Designed with heavy duty insulator that provides unparalleled dielectric strength and thermal conductivity under extreme temperatures
• Five-rib design prevents flashover while decreasing voltage loss
• Copper glass seal bonds the center electrode and insulator together for a gas-tight seal
• Platinum center electrode utilizes platinum to shrink the surface area of the center electrode tip for maximum firing performance and minimum voltage requirements
• Platinum ground electrode resists gas and electrical erosion and corrosion extending service intervals to 60,000 miles

Series: Denso Iridium Power

Quantity Sold: Sold individually

Warranty: 12-month Denso limited warranty

Part #: NPIT16